--------------------------------------------------------------------------------------------
-----
@R3
show diag
VWIC2-2MFT-T1/E1, VWIC-2MFT-E1인지 확인
gateway type : cisco 2801 -> next
protocol : MGCP- > next
--------------------------------------------------------------------------------------------
R1, R2, R3 도메인 이름 및 DHCP Relay Agent 설정 (x는 라우터 번호)
@ R1, R2, R3
conf t
ip domain-name cisco.com
!
int fa0/0.10x
ip helper-address 142.100.64.11
end
___________________________________________________________________________________________
2. IP Phone 등록
1) IP Phone 및 CIPC 등록
2) End User 생성 및 IP Phone/CIPC 연동
--------------------------------------------------------------------------------------------
3. PSTN 연결을 위한 트렁크 구성(CCS 방식)
1) 보이스 게이트웨이 트렁크 타입/체널 및 MGCP 설정
@R3
card type e1 0 2
network-clock-participate wic 2
isdn switch-type primary-net5
!
controller e1 0/2/0
pri-group timeslots 1-5 service mgcp
!
int s0/2/0:15
isdn bind-l3 ccm-manager
isdn outgoing display-ie
isdn outgoing ie redirecting-number
!
mgcp call-agent 142.100.64.11
mgcp dtmf-relay voip codec all mode cisco
mgcp sdp simple
mgcp bind control source-interface lo0
mgcp bind media source-interface lo0
mgcp
!
no mgcp
mgcp
-------------------------------------------------------------------------------------------
Domain Name: R3.voice.com
Description : R3.voice.com
Module in slot 0 NM- 4VWIC-NBRD 후 save
subunit :VWIC2-2MFT-T1/E1
--------------------------------------------------------------------------------------------
-----
Device Pool : SC-Pool
Signficant Digits : 4
--------------------------------------------------------------------------------------------
-----
PRI protocol Type Specific information
FRI
위에 3개 체크
----------------------------------------------------
See Endpoints클릭
R3# show isdn status
Global ISDN Switchtype = primary-net5
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply
ISDN Serial0/2/0:15 interface
dsl 0, interface ISDN Switchtype = primary-net5
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x8000001F
Number of L2 Discards = 0, L2 Session ID = 0
Total Allocated ISDN CCBs = 0
---------------------------------------------------------------------
show diag
show isdn status--> TEI_ASSIGNED (버그 상태임)
Rx#wr
reload
밑에 S0/SU2/DS1-0@R3.voice.com이 생성되면서 status상태가 registered됨
-------------------------------------------------------------------------
R3#show isdn status
Global ISDN Switchtype = primary-net5
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply
ISDN Serial0/2/0:15 interface
dsl 0, interface ISDN Switchtype = primary-net5
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
ACTIVE, inactive이면 케이블연결안됨
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED(정상)
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x8000001F
--------------------------------------------------------------------------------------------
------------------------------------------------------
4. 파티션 및 CSS 생성
- 각각의 사이트마다 Route-Pattern를 생성하기 위해서 생성해야 한다.
1) 파티션 생성
Call Routing -> Class of Control -> Partition
HQ-PT HQ-PT-A
SC-PT SC-PT-A
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
add new
name SC-PT-A
Line [1] - 3002 in SC-PT-A 클릭
Route Partition SC-PT-A
save
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
device- Phone -find
device name 클릭
왼쪽 상단에 생성된 line no partion클릭
Route Partion : SC-PT-A로 설정
save
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
오른쪽
* device infomation
DEvice name SEP000C291FE8B2
Device Pool SC-POOL-A
calling Search space SC-CSS-A
location SC-location-A
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
2) CSS 생성
Call Routing -> Class of Control -> Calling Search Space
add new
name : SC-CSS-A
Description SC-CSS-A
Available Partion 전체 설정한 파티션
selected pation 자신이 설정한 파티션을 선택한다.
save
3) CSS를 IP Phone 적용 -> reset 실시
Device -> Phone -> 사이트 전화기 클릭 -> CSS 적용 -> Save -> Reset 실시
--------------------------------------------------------------------------------
5. Route Group 및 Route List 생성
- Gateway를 Route Group으로 생성한 이후, Route List에 포함시킨다.
- 그래서 패턴 생성시 게이트웨이를 Route List로 선택하여 사용한다.
- 이유 : 게이트웨이 2개 이상 사용할 경우(Ex : TEHO 콜)
- 순서 route-group-> route-list -> router-pattern
Use Calling Party's External Phone Number Mask 체크 선택 안함
1) Route-Group 생성
Call Routing -> Route/Hunt -> Route Group
2) Route-List 생성
Call Routing -> Route/Hunt -> Route List
2) Route Pattern 생성
Call Routing -> Route/Hunt -> Route Pattern
HQ SB SC
긴급 9.11[239] 9.11[239] 9.911
9-599-1234 9-499-1234 9-799-1234
시내 9.[2-9]XXXXXX 9.[2-9]XXXXXX 9.[2-9]XXXXXX
9-032-499-1234 9-02-599-1234 9-1-702-399-1234
시외 9.0[3-6]X[2-9]XXXXXX 9.02[3-6][2-9]XXXXXX 9.1[2-9]XX[2-9]XXXXXX
국제 9.001# 9.001!# 9.011!#
9-001-2-312-799-1234# 9-011-82-02-599-1234#
9-011-82-032-499-1234#
휴대폰 9.010XXXXXXXX 9.010XXXXXXXX 9.010XXXXXXXX
Route Pattern: 9.911
Route Partition: SC-PT-A
Description : SC-Emergency
Provide Outside Dial Tone : 2차 다이얼통
Discard Digits : predot
R3 시외전화 Prefix Digits (Outgoing Calls) :1
-------------------------------------------------------------------------------------
7. Tollby Pass (TEHO 콜)
1) Route List 생성
Call Routing -> Route/Hunt -> Route List
2) Route Pattern 생성
Call Routing -> Route/Hunt -> Route Pattern
---------------------------------------------------------------
트렁크 구성
@SC
90018002.[2-9]XXXXXXX
-----------------------------------------------------------------------
8. SRST
cucm장애시 라우터가 콜매니저
1) SRST 구성
System -> SRST -> Add New 클릭
2) Device Pool에 SRST 적용 및 Reset
System -> Device Pool -> 사이트-Pool 클릭 -> SRST 선택 -> Save -> Reset
3) IP 전화기 확인
CIPC -> 셋팅 버튼 -> 2. Device Configuration -> 1~2번 항목 확인(Primary 142.100.64.11,
Backup 13.13.x.x)
IP 전화기 -> 셋팅 버튼 -> 3. Network Configuration -> 21~22 번 항목 확인(Primary
142.100.64.11, Backup 13.13.x.x)
@ R1, R2, R3 (x는 라우터 번호)
application
global
service alternate default
!
ccm-manager fallback-mgcp
!
call-manager-fallback
secondary-dialtone 9
ip source-address 13.13.3.3 port 2000
max-ephone 10
max-dn 10 dual-line
system message primary SC -SRST Mode
date-format yy-mm-dd
time format 12
dialplan-pattern 1 312747.... extension-length 4
6) IP 전화기 확인 (전체 메세지 사이트 이름-SRST Mode 확인)
CIPC -> 셋팅 버튼 -> 2. Device Configuration -> 1~2번 항목 확인
IP 전화기 -> 셋팅 버튼 -> 3. Network Configuration -> 21~22 번 항목 확인
show ephone
'네트워크/서버/모의해킹 > IPT' 카테고리의 다른 글
17.4.10 40일차(VoIP/IPT - 02. CME를 이용한 IPT 서비스 구축-4) (522) | 2017.04.10 |
---|---|
17.4.07 39일차(VoIP/IPT - 02. CME를 이용한 IPT 서비스 구축-3) (503) | 2017.04.07 |
17.4.06 38일차(VoIP/IPT - 02. CME를 이용한 IPT 서비스 구축-2) (495) | 2017.04.06 |
17.4.05 37일차(VoIP/IPT - 02. CME를 이용한 IPT 서비스 구축-1) (511) | 2017.04.05 |
17.4.04 36일차(voip,ipt) (495) | 2017.04.04 |